Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Furnace Repair Across Kenmore
Most furnace repairs in Kenmore run $150 – $700 and are finished same day, with our crew dispatching from our Seattle office to reach homes from Inglewood-Finn Hill to the Sammamish River shoreline. If your furnace is blowing cold air, short-cycling, or not keeping up on a January night, call (984) 538-9003. A live person answers, 24 hours a day, and we’ll send your technician’s name, photo, and background-check verification before anyone arrives at your door.
Kenmore’s lakeside location at the north end of Lake Washington creates a wetter microclimate than neighboring Bothell or Mountlake Terrace. That trapped marine moisture accelerates rust inside electric forced-air furnaces and corrodes blower motors in crawlspaces that never fully dry out. We’ve worked on enough 1960s split-levels off NE 181st Street and ranches near Bastyr University to know that a furnace that tests fine electrically can still be rotted through from humidity wicking up from below. Our Furnace Repair team doesn’t just swap parts; we diagnose why the part failed in the first place.
Why Brandt HVAC Is Kenmore’s Preferred Furnace Repair Company
We’ve earned our reputation in Kenmore by showing up with our Threshold Verified standard: every technician background-checked, identity-verified, and introduced by name and photo before arrival. When you open your door, you see the same face you were sent. If anyone different shows up, that visit is on us.
Our response time to Kenmore neighborhoods typically runs under two hours for no-heat calls, because we coordinate dispatch from our Seattle office and route crews directly to Inglewood-Finn Hill, Arrowhead, and the lakefront streets without backtracking through other markets.
Kenmore homeowners specifically mention our upfront pricing in reviews: a written cost before any work starts, no exceptions. Every repair carries a written 365-Day Done Right Promise. If it fails, we return at no charge. No argument, no additional fee.
We know the local housing stock. Most Kenmore homes were built during King County’s unincorporated era, before 1997, with electric baseboard heat and no ductwork. When we repair an aging electric forced-air system or advise on a heat pump retrofit, we’re working with the actual constraints of your house, not a textbook installation.
Furnace Maintenance in Kenmore
Furnace Maintenance in Kenmore means more than a filter swap and a quick look, because the north-end Lake Washington basin traps moisture that corrodes heat exchangers and breeds microbial growth inside air handlers. We perform a 22-point inspection that includes electrical connection torque checks, blower amp draw, heat exchanger visual inspection with borescope, and static pressure measurement against your ductwork’s original design. Most tune-ups in Kenmore run $80 – $200, and we schedule them before the October rains set in, when crawlspace humidity starts climbing toward winter peaks.
What We Find in Kenmore Crawlspaces
Our technicians document crawlspace conditions on every maintenance visit. Standing moisture between SR-522 and the lake shoreline wicks into plenums and corrodes blower housings from the outside. We flag vapor barrier failures and recommend sealed-crawl encapsulation before a $200 maintenance visit turns into a $600 blower motor replacement.
Electrical Panel Review
Many pre-1997 Kenmore panels lack spare capacity for modern equipment. During maintenance, we note available breaker space and amperage. If you’re considering a future heat pump conversion, this data matters now, not later.
Heat Pump Repair in Kenmore
Heat Pump Repair in Kenmore increasingly means servicing ductless mini-splits and electric forced-air heat pumps in homes that never had natural gas distribution. The same humid microclimate that rusts furnaces attacks heat pump coils and accelerates refrigerant leaks at flare connections. We repair all major brands including Rheem, York, and Daikin systems, with most calls running $150 – $700 depending on whether we’re sealing a leak, replacing a reversing valve, or swapping a corroded outdoor coil. Our trucks stock common Rheem and York heat pump parts for faster turnaround on Kenmore calls.
Coil Corrosion from Humidity
The Lake Washington basin’s persistent fog drives indoor humidity higher than Bothell’s upland neighborhoods. We measure wet-bulb temperature during every heat pump service call and clean evaporator coils with foaming cleaner rated for microbial growth. Ignored, that corrosion pinholes refrigerant lines within two seasons.
Defrost Cycle Problems
Kenmore’s mild winters with sudden cold snaps confuse heat pump defrost boards. We test defrost initiation temperature and termination sensors, then recalibrate for local conditions rather than factory defaults meant for drier climates.
Trusted Brands We Service in Kenmore
We service all major residential HVAC brands: Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. Our Seattle parts warehouse stocks Rheem heat pump components, York furnace control boards, and Daikin mini-split flare kits for same-day repair on most Kenmore calls. For older Bryant electric furnaces common in 1970s Kenmore ranches, we source OEM heat sequencers and limit switches without the two-week wait that sends homeowners to big-box universal parts that don’t quite fit. Every repair includes a written guarantee covering parts and labor for 365 days.
Common Furnace Repair Problems We See in Kenmore Homes
- Heat exchanger rust from crawlspace moisture. The low-lying streets between SR-522 and the lake shoreline see standing groundwater that wicks into plenums and corrodes steel heat exchangers from the outside. A furnace can pass a combustion analysis while being rusted through at the collector box.
- Single-zone thermostats fighting split-level layouts. The upstairs overheats while the downstairs never satisfies the setpoint. Homeowners blame the furnace; we measure static pressure and find 0.9 in. w.c. on ductwork designed for 0.5, with disconnected flex runs starving the lower level.
- Undersized electrical panels blocking equipment upgrades. A 100-amp Federal Pacific panel in a 1964 ranch has no room for a variable-speed air handler. We diagnose the panel constraint before quoting any equipment swap, so you’re not surprised by a $2,400 electrical upgrade after the furnace is already torn apart.
- Blower motor capacitor failure from voltage fluctuation. Pacific Power’s distribution in older Kenmore neighborhoods sees voltage sag during peak heating hours. We test capacitor microfarad readings under load, not just at rest, and spec hard-start kits where the grid struggles.
Pricing for Furnace Repair in Kenmore, WA
We publish our ranges because nobody should meet a stranger at their door without knowing what the work costs.
| Service | Typical Range in Kenmore |
|---|---|
| Furnace Repair | $150 – $700 |
| Tune-Up | $80 – $200 |
| Heat Pump Repair | $150 – $700 |
A failed ignitor replacement usually lands at the low end, around $150 – $300 parts and labor included. Heat exchanger replacement or blower motor swaps with electrical panel work push toward the upper range. What drives cost: accessibility of your crawlspace, whether the original ductwork needs sealing to stop the problem recurring, and if your electrical panel needs upgrading to safely support the repair. We give a written, fixed price before any work starts. No exceptions. Estimates are free. Call (984) 538-9003.
We Also Serve Cities Near Kenmore
Our crews work Kenmore daily and also respond to calls in Bothell, Mountlake Terrace, Lynnwood, and Woodinville. Dispatch routes from our Seattle office keep travel times short across the north Lake Washington corridor.
Serving Kenmore, WA - Our Local Coverage Area
We’re based in the Kenmore area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Furnace Repair in Kenmore
Yes, if you have an existing electric forced-air furnace with ductwork, we repair it. If you have only baseboard heat, there’s no furnace to repair, but we can evaluate whether a ductless mini-split heat pump or added ductwork makes sense for your home. Many Kenmore owners in this exact situation call us for a free evaluation of their options. Call (984) 538-9003 to schedule.
The north-end Lake Washington basin traps humid marine air that makes your furnace work harder to reach setpoint, and single-zone ductwork in split-level homes often overheats the upstairs while the downstairs lags. The thermostat satisfies upstairs, shuts off, and downstairs calls for heat again within minutes. We measure static pressure and zone balance to find whether it’s a ductwork problem, a failing limit switch, or both. Call (984) 538-9003 and we’ll diagnose it.
For a simple repair like a blower motor or ignitor, no. But if your furnace is over 15 years old and you’re considering any equipment change, yes, absolutely. Kenmore’s 1950s – 1970s homes were built with different insulation standards, and many have had windows and doors upgraded without updating the heating calculation. A like-for-like swap on undersized ductwork wastes money and comfort. We perform ACCA Manual J load calculations before any replacement quote. Call (984) 538-9003 to discuss whether your situation needs one.
Most furnace repairs in Kenmore run $150 – $700, with simple ignitor or limit switch replacements toward the lower end and heat exchanger or blower motor work toward the upper end. Crawlspace accessibility, electrical panel condition, and whether disconnected ductwork needs sealing all affect the final price. We give a written, fixed price before any work starts. Estimates are free. Call (984) 538-9003.
Yes, significantly. Standing moisture between SR-522 and the lake shoreline wicks into plenums and corrodes heat exchangers and blower housings from the outside in. We inspect for rust, recommend vapor barriers or sealed-crawl encapsulation, and spec corrosion-resistant components where standard parts would fail again within two seasons. Ignoring the moisture source turns a repair into a repeat callback. Call (984) 538-9003 and we’ll assess your crawlspace conditions.
We were called to a 1962 split-level off NE 181st St near the Sammamish River, where the homeowner’s 20-year-old Carrier electric forced-air furnace was short-cycling and heating two rooms while the rest of the house stayed cold. Our tech pulled the blower motor, found the run capacitor reading well below spec, and also measured static pressure at 0.9 in. w.c. – nearly double what the original single-zone ductwork was designed for, confirming the trunk was undersized for the home’s actual load calculation. We replaced the capacitor, sealed two disconnected flex runs to the upper bedrooms, and the system held temp across the whole floor plan on the follow-up visit.
Kenmore’s 1950s – 1970s lakeside ranch and split-level homes were built with electric baseboard heat and no ductwork, and most of the city has no natural gas distribution – so furnace repair here usually means fixing aging electric forced-air equipment or advising on a heat pump retrofit, not swapping a gas unit. Because the north-end Lake Washington basin traps marine moisture, indoor humidity runs higher than in Bothell, accelerating heat exchanger rust and blower motor corrosion inside older air handlers. A like-for-like furnace swap in one of these homes often disappoints because the real problems are undersized original ductwork, single-zone temperature imbalance, and electrical panels that can’t support modern equipment. We diagnose the house, not just the box.
Ready to get your heat back? Call (984) 538-9003 now. A live person answers, 24 hours a day, 7 days a week. We’ll send your technician’s name and photo before arrival, give you a written price before any work starts, and back every repair with our 365-Day Done Right Promise. Free estimates. No voicemail. No callback queue.
Written by Devin Marlowe, Owner at Brandt HVAC, serving Kenmore since 2003 as part of the Threshold Group family of home-service companies.